The Foundation of Plumbing Knowledge for Bathtub Installation

Set Up An Appointment

Have you been looking for critical information on How to Install a Bathtub Yourself?


How to Install a Bathtub: Install an Acrylic Tub and Tub Surround
Mounting a tub isn't specifically brain surgery, but it does need strong plumbing, carpentry, as well as sometimes, tiling abilities. Changing an old bathtub with a brand-new one is likewise a reasonably tough project. If the old tub is readily obtainable, the project can relocate easily; if you have to open up a wall to get rid of the old tub and position the brand-new tub, the job is a lot harder. In either instance, the project is within a residence handyman's skills, although you will need a helper to leave the old tub and also set in the new one. Make certain you have qualified yourself for the task and fit trying it. Rather than working with a service provider to take control of a halfway-completed task, it is far better to consider employing one prior to you start. Opportunities are you might need a professional plumber to make tube links.
This article will aid you install a brand-new tub in your bathroom if you have actually already gotten a brand-new tub and do not need to alter the setup of your previous water system pipes.
Your devices as well as product checklist must make up the following:
  • New Tub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Knife

  • Tape Measure

  • Pipe Caps


  • Preparing for the Installment


    Firstly, the supporting frame supplied with the bath should be fitted (if needed) according to the supplier's directions. Next off, fit the faucets or mixer to the tub. When suitable the faucet block, it is necessary to make sure that if the faucet comes with a plastic washing machine, it is fitted between the bathroom and also the faucets. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the faucets unit to prevent stress on the bath tub.
    Fit the flexible faucet connectors to the bottom of the two faucets using 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next off, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. Make sure you use all of the supplied washing machines.
    Attach the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bath must currently be ready to be suited its final placement.

    Removing Old Taps


    If you require to change old taps with new ones as a part of your setup, after that the first thing you should do is detach the water supply. After doing so, switch on the faucets to drain pipes any type of water remaining in the system. The process of removing the existing faucets can be quite problematic as a result of the restricted access that is frequently the case.
    Use a container wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipelines to the faucets. Have a towel ready for the remaining water that will originate from the pipes. Once the supply pipelines have been removed, make use of the same device to loosen the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from turning during this procedure. Once the faucets have actually been eliminated, the holes in the bath/basin will have to be cleaned up of any type of old sealing compound.
    Before proceeding to fit the brand-new faucets, contrast the pipe connections on the old faucets to the new taps. If the old taps are longer than the new taps, after that a shank adapter is needed for the new faucets to fit.

    Setting up the Bath tub


    Using the two wooden boards under its feet, put the bath tub in the called for position. The wood boards are handy in evenly spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 little factors.
    The following goal is to make certain that the bath tub is leveled all round. This can be achieved by inspecting the level as well as readjusting the feet on the bathtub until the spirit level checks out level.
    To set up faucets, fit all-time low of the furthest versatile faucet connector to the proper supply pipe by making a compression sign up with; then do the very same for the other faucet.
    Turn on the water system and examine all joints and brand-new pipework for leaks and also tighten them if needed. Load the tub as well as additionally inspect the overflow electrical outlet and also the normal outlet for leaks.
    Finally, deal with the bath paneling as explained in the producer's user's manual. Tiling and sealing around the bath tub should wait until the tub has actually been used at least once as this will settle it into its last placement.

    Fitting New Touches


    If the tails of the new taps are plastic, then you will need a plastic port to prevent damage to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end provides a connection to the current supply pipelines.
    If you require to fit a monobloc, then you will need minimizing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipe.
    Next off, place the tap in the installing hole in the bath/basin making certain that the washers are in area in between the tap and also the sink. Secure the tap in position with the maker offered backnut. As soon as the tap is firmly in place, the supply pipes can be linked to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with normal faucet connectors. The former type ought to be connected to the tap finishes first, tightening just by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been attached.

    Tiling Around the Bath tub


    In the area where the bathroom fulfills the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to fracture a rigid seal, triggering the water to permeate the wall surface in between the bath as well as the tiling, resulting in problems with dampness and also feasible leaks to the ceiling below.
    You can pick from a range of coloured sealants to assimilate your components as well as fittings. They are sold in tubes and cartridges, and also are capable of sealing spaces approximately a size of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to always fill the bathtub with water before securing, to allow for the activity experienced when the tub remains in usage. The sealer can split relatively very early if you do not take into consideration this motion prior to sealing.
    Additionally, ceramic coving or quadrant ceramic tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise conveniently available on the marketplace. It is a good idea to fit the floor tiles utilizing water-resistant or water resistant adhesive and also grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub

    Do you enjoy reading up on Installing A Bathtub? Give feedback down below. We would be pleased to find out your insights about this blog. In hopes to see you back again in the near future. Sharing is nice. Who knows, you may just be helping someone out. We thank you for reading our article about How to Install a Bathtub.


    Protect your property; contact now.

    Leave a Reply

    Your email address will not be published. Required fields are marked *